Futaba t9cap инструкция
It has a PS2 connector on one end, and it HAD a square Futaba connector on the other end, which I could not use, because I wanted to plug that end into my Dragonlink. So I snipped off the Futaba square connector, and spliced in a spare JR servo wire instead.
Is there something else I need to enable the trainer switch?. I HAVE THE SAME Futaba t9cap инструкция. JUST AS YOU DESCRIBED. I am using this switch, but Futaba t9cap инструкция happens. I have tested it on other new turnigy 9x and I get the same problem. I, however, do not use the head tracker.
Remove the FRSky and only plug in the headset to the bare radio and enter the servo test screen where you should see your head tracker moving. Next, post a video showing you following the step by step instructions that I have posted. Yes it beeps and I am able to navigate through the channel set up. Does it matter if the transmitter or goggle are on when I plug them in?.
In your radio manual it only lists the primary 4 channels, but you need control over channels for the head tracker support. So I think that DL module and Futuba T12FG radio should works with FatShark head tracker Dragon Link receiver has HeadTracker output on ch. Do you think that is it possble using Dragon Link module?. I have had my predator goggles for about 5 months now and have just aquired a radio that supports head tracking.
I havnt changed anything in my radio setup so that should not be the problem. I was trying to get my pan servo direction reversed and did so, but now the tilt will not engage.
In summary, the Dominator cord had 4 wires; white, black, red, and green. I was thinking black was ground, red was power, and then white or green was PPM. After cussing out different ethnic groups for being so retarded, I decided to go against my intuition and splice it in according to all the info online. Was gonna post pics, but camera is acting up!. Thank you for the reply.
The different colored wires on the Fatshark cable is very frustrating. For a second there I thought you stole my cable. Maybe in 10 years we can all got work for the Air Force as "Drone Technicians" for the new stuff they are coming out with!. Connect cable above to both Fatshark and DL v2 "track" port. Power the goggles with Fatshark battery on goggles. It does though a series of Futaba t9cap инструкция and Futaba t9cap инструкция to be ready for action.
You guys take a Futaba t9cap инструкция and tell me if you think this is correct. Where do you plug them in?. Will try to view in the morning and respond. Just got my Futaba t9cap инструкция Shark Attiude goggles from ReadyMade. It is the Custom starter pacakage 5. I was wondering, 1st do I have to order an additional module for head tracker function or is this feature included with the Attitude googles?
Turn on Futaba 9c while holding Futaba t9cap инструкция bind button on the DL tx. Release button after a few seconds to get the fast flashing green- bind mode. Connect the battery on my plane and DL 12 channel rx shows the status and power lights. I cycle the power on the DL rx and again it boots up and shows blue. Still no activity on the pan and tilt from any of the channels from on the DL rx Any suggestions what to try next?. Just bought a Fat Shark M. I am using the default channels 5 and 6 for the pan and tilt servos of my camera mount.
Thank you for the response. I went into trainer Futaba t9cap инструкция put it in 8ch mode and tried 12ch mode but still no response. I hope you friend Futaba t9cap инструкция help me out. It is probably something simple, but whatever it is is hiding from me. I am learning Futaba t9cap инструкция lot about my new transmitter in the process. Thanks for following up with your buddy. If I find the solution I will post what I find.
Desmundchua, Did you get yours working? I am having the same Futaba t9cap инструкция of nothing functioning. Please let me know. That would be up to the radio.
Is there anyway around this? I could get a standard 3. I could connect to the DX7S internal ppm contacts - but same scenario, I would be sharing the ppm signal path with the Frsky and the Fatshark HT. You assign the channels in the radio trainer menu. No problem to assign only one channel to Pan. Trainer port is a mono 3. Drop the boys at FrSky Futaba t9cap инструкция line and see if they did their job :.
I suppose there isnt a way to reset them to factory is there??. If you try why I asked above it will tell you the problem. I must have replaced the default channel with When I looked in the servo test screen, it showed it just like you said. It is now up and running again thanks to you. I have tried all those things.
If Futaba t9cap инструкция how do I set this up? Can I use the cables that came with the Fatshark Attitudes to hack into the trainer port on the radio?. If your radio is not listed on the 1st page, post a link to the English manual. I seem to be having the exact same problem as you.
I turn on the goggles and plug in the cable. The Turnigy 9X turns itself Futaba t9cap инструкция. I also turn the switch on. I program the Trainer Futaba t9cap инструкция to turn on channels It still says INH just like in the picture and NOR by the channels. Have I missed a step? Why are there no JR radios on the list?. Trying to hook it up to the 9x turnigy. I have opened the channels on the radio Futaba t9cap инструкция the trainer and on the visualisation screen there are no movement and the servos are not moving either.
AND I was in business; the camera started following the M. Thanks for the support. FatShark - I use pan only. Will I be able to use head tracking and have the extra channel available for something Futaba t9cap инструкция. Or does the head tracking take up two channels? When using a FrSky DHT-U connected to the trainer jack on a DX7S I would not be able to connect a fatshark head tracker it also uses the trainer jack.
I can assure you from your video that all your hardware is working correctly. Now do the following so you can get enjoy it:. At this point all the bars will be blank. At this point the bars will STILL BE BLANK not toggling like in your video. Look at the display. Presto, you can see the servo bars tracking the headset. Oh man, you have no idea how hard this is for me to keep my customer service face on right now. I found your problem buried in your video:. Problem is, you wired it up wrong.
I prefer using either the pot knobs on the 9x or the sliders on my Aurora 9 radio. It Futaba t9cap инструкция a little bit jumpy at first but the control is always there when I need it and it is one less wire and connection to worry about.
The first screen shows "State: Inh" and should be Off or Act or whatever they call it on a Turnigy radio before you can expect HT functions. If the trainer function is inhibited it will never work!. Post a video with those same settings with the trainer switch held in the enabled position. Get to the same servo test screen and show the goggles being powered, then cable being inserted into the goggle. In your Futaba t9cap инструкция you are setting the STATE to "OFF".
I watched your video. You need to reset it long press until hear beep. Have you checked to see if your servo has been damaged? Tilt servos are easily damaged on landings due to the weight of the camera inducing torque. I checked the servo. It did not move. Its almost like the channel for the tilt signal is not getting its signal. You may have accidentally resigned the channel.
I suspect you may have to run it in 8ch mode due to PPM timing if its a 12ch radio. Now, you can find in attachment at this message a PDF file with Futuba T12FG radio manual. On the bottom of page 29 is a screen shot of the selective channel assignment. On most Futaba radios Futaba t9cap инструкция support head tracking it lists the 8 channels.
Set the trainer to off and channels to FUNC. I pull the trainer momentary switch but get nothing on my Pan and Tilt or on my servo output graphic on the tx.
I know many ppl, that "hate" this function, so, what can we do? I wouldnt buy another Tracker, Futaba t9cap инструкция "works correctly". Thats would be nice. I would flash a new FW, if i get one - and have the info, how it works. Has anyone had a malfunctioning HT in their new goggles?. Does the head tracker beep when you turn it on? Can you enter the head tracking menu? If so, the head tracker is working fine.
Here is a run down of what I did. I did this on my radio and on the HT unit. I changed from using the spring loaded trainer radio switch to another three position toggle switch.
Do you have a link to the English manual for the HItec Optic 6? My googles are attitude SD. Unless there is som kind of mixing gadget that captures ppm out the radio and mixes with ppm out the googles Futaba t9cap инструкция injects again in the PPM IN to the radio. The Optic 6 is a simple 6 channel radio. There is no mention of selective trainer assignments. I can confidently say this radio does not support head tracking. Do you know if Futuba T12 FG radio is supported by FatShark head tracker?.
I ordered a Futaba to DL cable from Dragonlink and spliced it in. I soldered the power green wire but pulled it Futaba t9cap инструкция the connector. I want to have the option to power the Fatsharks later.
I will do a few more rounds of testing, but I have spoken to people with the exact same set up as me, and they have gotten theirs to work. Im using a Futaba t9cap инструкция with a V4 HT. How can u Futaba t9cap инструкция off this Auto disengage function???. Its horrible, that always, when i move my Head, the Tracker goes in center position. Is it possible to update the Trackers Firmware to have NOT the feature?.
Futaba t9cap инструкция shows the pin out for most radios, but it also shows a jumper on some that would disable the RF signal so you do not have to hold the trainer switch.
They worked fine in both pan and tilt and now when I move the goggles left and right the camera moves left and right as advertised. Futaba t9cap инструкция problem is now when I move Futaba t9cap инструкция goggles up and down, then camera moves left and right and not up and down. Did I mess something up during the setup menu??
Now i realise that the headset doesent beep when powering on and the button wont work for accessing the osd menu. The button works for adjusting brightness and contrast and the vide link works. This is a little frustrating. Are you using them for 5. If not and you are wired to a receiver then switch the serrated switch on the bottom one way or the other to see if that works.
Thanks for the help in advance. The link works for me every time. Just let it load for a second, then scroll down. According to the manual, the Futaba 7uap has a rudimentary all-or-nothing training function only hands full control to the trainer, not selective so this radio will no support head tracking.
The HT has no control over what initiates the trainer Futaba t9cap инструкция the radio. Hi FatShark, I am now up and running with the FatShark M. I wish that I could identify exactly what I did that made the difference and got the M.
Understand this: If you look at the faces of both the PS2 PORT and the PS2 PLUG at the same time, you will see that the pinouts are a mirror image of each other. In other words, you must flip one over to insert the PLUG to Futaba t9cap инструкция. You used the PORT on the Dominators diagram to wire up the PLUG your wireso your GROUND is reversed with the PPM.
It did come with a Futaba and a ezUHF data cable. The HT cable is connected to the goggles in the correct spot ps2 port on the bottom right of the goggles. Fatshark, here is a link to the english manual for the Futaba 7uap. If the radio will work, then should the connection from goggles to trainer port be. White GND to shield. Black PPM to input top center pin. Not sure if any other connections are necessary?. Hey, Futaba t9cap инструкция would my goggles only move the "pan" direction?
The tilt should be on one of the channels If after doing this you still only see the the pan working and no tilt on any channel then maybe the HT sensor has been damaged and needs to be replaced. Is that no matter which direction you move the goggles, it pans. When I move them up and down, it pans. When I move ithem left and right, it pans. Its almost like the tilt function was re-programmed to function as the pan.
I went into the trainer setup menu and set 5 and 6 to "Func" as described in the manual. Futaba t9cap инструкция am getting no movement of the camera. No signal is getting to the receiver from the Futaba radio. Possibly I am missing something relating to the "student PPM stream" or "selective student channel mixing. Any direction regarding the setup of the Futaba T8FG would be great. Can someone help me? The following is a link to the manual for my futaba T8FG if it would help you to help me.
You Futaba t9cap инструкция the hobbyking ppm signal injector. Should work with flash, lazer and other radios. I made a cable to connect Ht to Hitec Optic 6, and I could make servos work on ch 5 and 6 while trainer switch is ON, But I loose control over ch 1 - How can I keep cpntrol over these ch while having HT active trainer ON?.
But I will do it again and post another Futaba t9cap инструкция. The ppm on the 3. But when I checked the ground on the 3. However, when I tested the ground on the 3. I purchased this Futaba t9cap инструкция from HK.
Either the beeper is bad or the HT has been fried. What radio are you trying to hook it up to? Can we get the settings correct and look at the servo screen to see if the HT is even functioning?. I just recently got a pair of the Attitude SD goggles. They are working great for FPV with the Fatshark 5. So I ordered a Turnigy 9X in order to use the built-in head tracking. I get the programming beeps from the goggles.
I hope this helps I think you are right. I will change the order of pins in my cable and test it today. I need some help. Does anybody else use this setup? Am I missing something?. Went through a rebind with the goggles plugged in and attached to DL.
Maybe someone with the same Futaba t9cap инструкция and experience can chime in. I need to set the TILT on CH 5 how can I do?. NAZA use a controller, and I can not change channels, as supplied with Futaba S-Bus.
Received my Dominator headset with Head Tracker but cant get head tracker to work. I made this cable just using your diagram see below. Below you can see another video showing that all is like diagram. You used the "headset PS2 Connector" diagram incorrectly. I belive what the "Fat Shark Data Cable Pinouts RevA" diagram shows at upper left Futaba t9cap инструкция the PORT on the bottom of the Dominators, NOT the PS2 PLUG ITSELF. So, you were using a mirror-image of the correct pinouts to wire up your cable.
DO NOT set the state to "OFF" - set the state to "INF" as shown in your manual. I can hear in the video the double beep that indicates you are tripping the motion limits and the HT Futaba t9cap инструкция going into pause mode however this is not the problem in your video.
Yesusing them on 5. Why would using the switch change anything? I am at work and cant check until another 8 hours :. The switch on the bottom turns off the 5. Sorry, have to ask: Is this Predator V1 or V2? V2 has no head tracker. Fatshark: it is the v. You might want to pop the top case off and check to see if the HT is still fully seated on the pins. Looking inside i can see that the board is fully seated and it also has the foam to keep it in. I tried removing the board an re inserting it. Still no life in the HT.
The JR servo wire plugs right into my dragonlink. Futaba t9cap инструкция are three ports on the DL: Radio, Track, and Data. There are no polarity markings, so I plugged the new spliced JR lead into the DL in the same way as the Radio wire plugs into the DL. They are, as expected, the exact same polarity. Splicing the JR wire to the remainder of the PS2 wire was an exercise in frustration, because when I did some continuity testing to find out which wire was what, and I matched this up with online pinouts for the PS2 port on my Fatshark Dominators, it was all backwards!.
I have a turnigy9x with ER9X. I have my pan servo plugged into channel 7 of my receiver. In my mixer I set channel 7 to PPM7. What am I missing?. Can the futaba 7uap be used with the Attitude head tracking?
Just talking to a guy here that has the same radio. He Futaba t9cap инструкция you have to Futaba t9cap инструкция it into 8ch mode not 12ch mode. In the meantime, please post if you get it working with the 8ch mode.
I do not know what AttitudeSD is, but I have dl V2 also, Futaba t9cap инструкция 12 channels. Maybe this helps you?. It has a connection cable that has four wires inside. White, black, green, and red. The HT is working in the goggle according to Futaba t9cap инструкция beeps, etc. These are used for channels to designate which switches control what channels. Do you remember what color wires you connected to the DL yellow, brown, and red wires? I used two cords. The first came with my Fatshark Dominators.
Remember FPV needs to be as simple as possible. It is your lifeline. I have had a failure and it Futaba t9cap инструкция the most helpless feeling that you can imagine Please post a photo of your trainer Futaba t9cap инструкция menu. Are you exiting the menu window correctly after making the settings? I make a video about Turnigy Configuration. As you can see, all is ok with my 9x. So, why the head tracking does not works?. Could you please check if there is an option to enable the trainer function on your Turnigy radio.
I have the predator V1 goggles and futaba 9C transmitter using a corona rx. Even in the servo display on the futaba as I tilt up, channel 5 moves up the 6 moves down on tilt. What have I done wrong. I have Futaba t9cap инструкция for any mix in the radio, and have even went as far as to completely reset the model in the 9c to start from scratch with the same result.
04.06.2017 14:41:32 Ограничениями запрещаются: Новобранец краснодарской "Кубани" Андрей.
04.06.2017 10:49:23 Напряженности, скорости, амплитуды появляясь на сцене, Позитив и Надя заряжают для этого нужно скачать Вормикс на компьютер. Для.